DEVICES YOU NEED TO SET UP A NEW BATHTUB

Devices You Need to Set Up a New Bathtub

Devices You Need to Set Up a New Bathtub

Blog Article

Further Details

Are you on the lookout for advise concerning How to Install a Bathtub?


How to Install a Bathtub
Installing a bath tub isn't precisely rocket science, but it does require strong plumbing, woodworking, and also often, tiling skills. Replacing an old bath tub with a brand-new one is likewise a reasonably tough job. If the old tub is readily accessible, the project can relocate easily; if you need to open a wall to remove the old bathtub and also place the new tub, the task is much harder. In either instance, the task is within a house handyman's skills, although you will need an assistant to vacate the old bathtub as well as set in the brand-new one. See to it you have actually qualified yourself for the job and also fit attempting it. Rather than working with a specialist to take over a halfway-completed job, it is much better to think about employing one before you start. Opportunities are you might need a professional plumber to make tube connections.
This article will certainly aid you set up a brand-new tub in your bathroom if you have currently gotten a brand-new tub and also don't need to alter the arrangement of your previous water pipelines.
Your devices as well as material checklist need to make up the following:
  • New Tub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Shatterproof glass

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Knife

  • Tape Measure

  • Pipe Caps


  • Planning for the Installation


    First of all, the supporting structure supplied with the bath needs to be fitted (if needed) according to the producer's instructions. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is important to make certain that if the tap features a plastic washing machine, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is also reasonable to fit a supporting plate under the taps device to prevent pressure on the tub.
    Fit the flexible faucet connectors to the bottom of both taps using 2 nuts as well as olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet through the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Make sure you use every one of the provided washing machines.
    Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bath should now prepare to be suited its last position.

    Removing Old Taps


    If you need to replace old taps with brand-new ones as a part of your installment, after that the first thing you need to do is disconnect the water supply. After doing so, switch on the taps to drain any type of water continuing to be in the system. The procedure of getting rid of the existing faucets can be fairly problematic due to the restricted access that is frequently the situation.
    Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipes to the taps. Have a fabric prepared for the staying water that will come from the pipes. Once the supply pipes have been removed, use the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from turning during this process. Once the taps have been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any type of old sealing compound.
    Before moving on to fit the brand-new faucets, contrast the pipeline connections on the old taps to the new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the new taps to fit.

    Installing the Bath tub


    Making use of both wooden boards under its feet, place the bathtub in the called for placement. The wooden boards are useful in evenly spreading the weight of the bath tub over the location of the boards rather than focusing all the weight onto 4 tiny factors.
    The next goal is to make certain that the tub is leveled all round. This can be accomplished by checking the level and also changing the feet on the bathtub till the level checks out level.
    To mount taps, fit the bottom of the outermost versatile tap adapter to the proper supply pipe by making a compression join; after that do the exact same for the other tap.
    Switch on the water as well as check all joints and brand-new pipework for leakages as well as tighten them if necessary. Load the bath tub and additionally inspect the overflow outlet and also the typical electrical outlet for leakages.
    Finally, deal with the bath paneling as described in the maker's instruction manual. Tiling as well as sealing around the bath tub ought to wait till the bathtub has actually been used at the very least once as this will certainly settle it right into its last setting.

    Suitable New Taps


    If the tails of the brand-new taps are plastic, after that you will certainly need a plastic adapter to avoid damage to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end gives a connection to the current supply pipes.
    If you require to fit a monobloc, after that you will call for minimizing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
    Next, place the faucet in the installing hole in the bath/basin making sure that the washing machines are in area between the faucet as well as the sink. Safeguard the tap in position with the producer given backnut. When the faucet is safely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet adapters. The former kind ought to be attached to the tap finishes first, tightening just by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been linked.

    Tiling Around the Bath tub


    In the area where the bath satisfies the floor tile, it is necessary to seal the accompanies a silicone rubber caulking. This is necessary as the installation can move enough to break an inflexible seal, creating the water to pass through the wall between the bathroom and also the tiling, leading to problems with moisture as well as feasible leakages to the ceiling below.
    You can choose from a range of coloured sealers to assimilate your components and fittings. They are sold in tubes as well as cartridges, as well as can securing gaps up to a width of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with spins of drenched paper or soft rope. Bear in mind to constantly fill the bathtub with water before sealing, to enable the motion experienced when the tub remains in usage. The sealer can split rather very early if you do not think about this movement before sealing.
    Alternatively, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also conveniently available on the marketplace. It is suggested to fit the tiles making use of waterproof or water-proof glue as well as cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub Yourself

    As a passionate person who reads about How to Install a Bathtub Yourself, I think sharing that information was a good idea. If you please set aside a second to promote this page if you enjoyed it. We love reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.




    Book A Free Estimate


    Report this page